Skip to main content

PROSAT® PSC20005

Saturated wipe

Back to our saturated wipes

The validated sterile wipes PROSAT® PSC20005 made of hydroentangled cellulose-polyester non-woven fabric are saturated with 70 % IPA / 30 % DI water (USP quality). They are especially suitable for a range of cleaning tasks in areas where validated sterility is required. The reclosable pouch maintains solvent saturation and cleanliness.

 

Facts

Particle emission (dry)
Particle emission (wet)
Abrasion resistance
Wet cleaning
Dry cleaning
Chemical permanence
Electrostatic behaviour
Softness
Sealed edges
decontaminated
sterile

Saturated wipes

PROSAT® PSC20005

Non-woven, 46% PES / 54% CEL, with 70% IPA / 30% DI water, validated sterile

-
-
-
-

Properties

  • 46% polyester/54% cellulose
  • non-woven fabric made of water jet entangled staple fibres
  • saturated with 70% IPA/30% DI water (USP quality)
  • validated sterile (SAL of 10-6)
  • reclosable PE pouch, packed in an outer bag

Advantages

  • reduced level of volatile organic compounds (VOC)
  • fast and efficient cleaning
  • reduces the storage of cleaning agents
  • easier to transport, store and use
  • even application of the cleaning solution

Application

  • wiping of objects before the airlock procedure
  • for quick and practical surface cleaning of equipment and parts 
  • wet cleaning of scratch-sensitive surfaces to specifically remove chemical residues

Product recommen­dation based on cleanroom classes


123456789low dust


ABCDE

Of course, cleanroom wipes used in ISO 5 can also be used in ISO 9, but in this case the economic efficiency and usefulness should be considered.

A 1 to 1 allocation of cleanroom wipes to an air cleanliness class according to ISO 14644-1 is not possible. Recommendations can only be made on the basis of special properties relevant from a cleanroom technical point of view, such as "abrasion resistance" or "particle emission". Users can find further information on this in VDI Guideline 2083 Part 9.2.

Technical data

Properties   Unit of measurementValueTest method
Material (fabric)     54% CEL / 46% PES  
Saturation solution     70% IPA (USP grade) / 30% DI water  
Edge processing     cut  
Mass per unit area   g/m2 53 manufacturer's specific
NVR
non-volatile residues)
IPA based
DI water based
g/m²
g/m²
not detected*
0.037
IEST-RP-CC004.3, Sec. 7.1.2
IEST-RP-CC004.3, Sec. 7.1.2
Particle residues ≥ 0,5 µm x 106/m2 18.6 IEST-RP-CC004.2, Sec 5.1
Fibre residues > 100 µm x 103/m2 21.7 IEST-RP-CC004.2, Sec. 5.2
Ionic residues Sodium (Na+)
Chloride (ClO2-)
ppm
ppm
11.9
18.2
IEST-RP-CC004.3, Sec. 7.2.2
IEST-RP-CC004.3, Sec. 7.2.2
Sterilisation validated sterile
per gamma irradiation
SAL (10-6) yes n.s.
  DimensionsPU per cartonArt. no.  
  9" x 11"
(~ 23 x 28 cm)
1,400 pieces
(50 pcs./Pouch)
double bagged
59808  
      * Levels are below detection limit of test equipment  

Note

The manufacturer's technical data listed above are typical values at the time of publication. They are not specifications. All data are without guarantee, changes are possible without prior notice.
Due to different test methods depending on the respective manufacturers and test laboratories, most of the given values cannot be compared one-to-one with those of other manufacturers/wipes.
Independent tests can be commissioned on request.

To top