Skip to main content
Dastex Reinraum ZubehörDastex Reinraum Zubehör

Series 410-IO

Polyester wipe

Back to our polyester wipes

The series 410-IO, a two-layer knitted wipe made of 100% polyester filaments. Cutting is done by laser, which simultaneously seals the wipe edges. Manufactured and packed in a cleanroom under ISO 4 conditions (EN ISO 14644-1). The double-layer welded wipes, even if they are made of polyester, have a high absorption capacity. The robust polyester knitted fabric shows its strength on rougher surfaces or on sharp-edged objects and/or surfaces. Relatively low levels of ionic and metallic contaminants. As efficient as series 410, but cheaper.

Facts

Particle emission (dry)
Particle emission (wet)
Abrasion resistance
Wet cleaning
Dry cleaning
Chemical permanence
Electrostatic behaviour
Softness
Sealed edges
decontaminated
sterile

Polyester

Series 410-IO

Knit, 100% PES filaments, double layer, laser-sealed edges

-

Properties

  • 100% polyester
  • two-ply interlock fabric made of filaments, ultrasonically welded and quilted
  • laser cut and sealed edges
  • very low particle and fibre emission
  • decontaminated in a cleanroom laundry
  • double bag packed in a cleanroom (air cleanliness class ISO 4)

Advantages

  • similar to Series 410, but cheaper
  • particularly absorbent due to double-knit construction
  • reduced particle and fibre emission due to sealed edges
  • wide range of applications, especially in the field of surface disinfection

  • validated sterile available

Applications

  • cleaning wipe especially for critical areas
  • cleaning wipe for areas where high absorbency and cleanliness are required
  • well suitable for angular, rough surfaces and objects which might prematurely damage a non-woven fabric wipe

Product recommen­dation based on cleanroom classes


123456789low dust


ABCDE

Of course, cleanroom wipes used in ISO 5 can also be used in ISO 9, but in this case the economic efficiency and usefulness should be considered.

A 1 to 1 allocation of cleanroom wipes to an air cleanliness class according to ISO 14644-1 is not possible. Recommendations can only be made on the basis of special properties relevant from a cleanroom technical point of view, such as "abrasion resistance" or "particle emission". Users can find further information on this in VDI Guideline 2083 Part 9.2.

Technical data

Properties   Unit of measurementValueTest method
Material     100% PES  
Edge processing     laser cut  
Mass per unit area   ± 10 g/m2 250  
Thickness   mils
mm 		n.s.
n.s. 		 
Absorptive capacity
(Ai) intrinsic
(Ae) extrinsic 		 
ml/g
ml/m2
2.1
460 		IEST-RP-CC004. 3
Absorbency rate   sec < 5 IEST-RP-CC004. 3
NVR
Non-volatile residues		 IPA based
DI water based 		µg/cm2
µg/cm2		 0.05
0.01 		IEST-RP-CC004.3
Particulate residues > 0.5 µm x 106/m2 8 IEST-RP-CC004.3
Section 6.2.1
Fibre residues ≥ 100 µm count/m2 190 IEST-RP-CC004.3
Ionic residues Ammonium (NH4+)
Chloride (ClO2-)
Nitrate (NO3-)
Potassium (K+)
Sodium (Na+)
Sulphate (SO42-) 		µg/g
µg/g
µg/g
µg/g
µg/g
µg/g
 0.50
0.80
0.80
0.20
0.60
0.30 		IEST-RP-CC004. 3
Organic contaminants silicone oil
amides
D-n-octylphthalate (DOP)
   n. d.
n. d.
n. d. 		by FTIR spectrometer
Fourier transform infrared spectrometer
  DimensionsPU per bagArt. No.  
  9" x 9"
12" x 12"
16" x 16" 		50 pieces
50 pieces
25 pieces 		55410-IO 0909
55410-IO 1212
55410-IO 1616 		 
      n. s. = not specified
n. d. = not detectable		  

Note

The manufacturer's technical data listed above are typical values at the time of publication. They are not specifications. All data are without guarantee, changes are possible without prior notice.
Due to different test methods depending on the respective manufacturers and test laboratories, most of the given values cannot be compared one-to-one with those of other manufacturers/wipes.
Independent tests can be commissioned on request.

To top